Fixed Power Resistor 4.7 Ohm 160W

Resistance 4.7 Ohm
Power rating 160 Watt
Resistance tolerance ±5%,  ±10%
Price Resistor FPT 160W 4.7 Ohm $5.00
Dimensions D×L×H×d 30×220×43×20 mm
Weight 240 g

Power fixed resistor 4.7 Ohm 160 Watt – wirewound load chassis and panel mount resistors of type FPT series (Fixed Painted Tubular Resistors). Resistor 4R7 160W – rated resistance is 4.7 Ohm, power dissipation is 160W.

Resistors with a specific rated power can also be manufactured to individual order. Other similar series of resistors are RX20, RXG, RXHG, FSE, FST, FVE, FVT, L150J.

PDFDatasheet PDF for Fixed Power Resistors.

PDFThe resistance values of resistors follow the E24 series.

Resistors are designed for using in AC and DC circuits, providing current limitation and voltage distribution. The maximum operating voltage at AC is 1000V, at DC – 1400V. Operating elevated ambient temperature does not exceed +155°C (at the same time the power is reduced to 60% of the nominal power), the limit temperature up to +250°C. The insulation resistance of wire resistors is at least 1000 MOhm. Working time – at least 15000 hours.

Structurally, the resistor consists of a tubular ceramic core on which a constantan (low resistance resistor) or nichrome (high resistance resistor) wire is wound. Resistors are coated with heat-resistant and moisture-resistant insulating paint.

Fixed value resistors have a defined ohmic resistance and are not adjustable.

Contacts, resistor leads are rigid, tape type with screw holes or for soldering conductors. Kind of mounting is hinged. Mounting of resistors on the panel is provided by a set of fasteners. Resistance tolerance is ±5%, ±10%.

Using the calculator, it is convenient to calculate the total resistance when the resistors are connected in parallel or in series, and the resistor resistance in the circuit.

Comparative characteristics of wire tube resistors, cement resistors and resistors in aluminium housing are presented in the comparative table.

Detailed resistor specifications, overall and mounting dimensions, mounting kit, installation and operation recommendations are given on the page below.

Our company is engaged in the production and sale of wirewound tubular resistors. All our products pass strict quality control and meet the necessary standards. Since we are the manufacturer, and in the price of the final product does not include dealer markups, we have low price saddle packing.

The warranty period of the resistors 160W supplied by our company is 2 years. Documents confirming the quality of products are provided.

Read more

The final price for 4.7 Ohm 150W 160W Watt Fixed Power Resistors depends on the quantity, delivery terms and form of payment.

For questions regarding the acquisition of Fixed Power Resistors 160W, send an email request to:

[email protected]

And we will provide you a commercial offer for delivery.
For a large number, we will provide an individual price!!!

We are open to manufacture products at our production facilities
according to your requests and technical task.

Electrical and technical specifications of Fixed Power Resistors 160 Watt:

Power rating 160 Watt
Series of nominal resistance values E24, PDFDatasheet of resistance values
Resistance tolerance ± 5%, ± 10%
Rated voltage Vmax = (Pnom × Rnom)0.5
Maximum working voltage 1400V
Operating temperature -60°C ... +155°C
Raised ambient operating temperature 70ºC
Relative humidity at 35°C without condensation <98%
Temperature coefficient of resistance ±500 ppm/°C
Insultation resistance 1000 MOhm
Life time 15000 hours
Dimensions D×L×H×d 30×220×43×20 mm
Weight 240 g

Part Numbering Guide for Fixed Resistor 160W 4.7 Ohm:

Resistor   FPT   160W   4.7 Ohm   ±10%
Resistor Product Name.
FPT Fixed Painted Tubular Resistor Series.
160W Rated Power, Watts.
4.7 Ohm Nominal Resistance, Ohm.
±10% Tolerance.

Mounting Hardware for Power Wirewound Tubular Resistors 160 Watt

Mounting hardware are used for mounting the resistors. Resistors can be supplied with a set of mounting hardware, including mounting brackets (corners), which must be ordered individually.

Photo Series of mounting hardware and brackets Price Dimensions, mm Weight
Threaded rod Ceramic bushing Mounting brackets Size between resistor axis and panel Size between resistor and panel
L Ød1 ØD Ød AxAxB k h
Hardware 160W HDW 160W $0.95
300 М5 30 18 30x30x15 24 9.5±1 64 g
Mounting Brackets 160W BR 160W (2 pcs.) $0.35
21 g

Completeness of Mounting Hardware for Power Wirewound Tubular Resistors

Image Completeness of Mounting Hardware
Item Power: 25W, 50W, 75W, 100W, 160W
Threaded rod M5 1 pcs.
Ceramic bushing 2 pcs.
Screw-nut M5 2 pcs.
Flat washer 2 pcs.
Spring washer 2 pcs.
Asbestos washer 2 pcs.
Brackets (Corners) 2 pcs.

Installation methods of tube resistors

At influence of mechanical factors for resistors the hinged way of installation is applied. The resistors are fixed to the mounting plates by mounting hardware:

  • resistor power from 3 to 25 Watt – cantilever or on two brackets at the ends of the mounting studs
  • resistor power from 50 to 160 Watt – only on two brackets at the ends of the mounting studs
Resistor mounting

Overall and Mounting Dimensions of Ceramic Tube Fixed Power Resistors 160 Watt:

Drawing of wirewound tubular resistor
L, mm ØD, mm H, mm Ød, mm Ød1, mm B, mm A, mm
220 30 43 20 3 6 4.5

Power Wirewound Tubular Ceramic Resistors by AS ENERGI

Our company is engaged in the manufacturer and sale of power wirewound tubular resistors fixed and adjustable types.
You can buy resistors from us in any volumes, and when ordering large lots, the price will be lower.
We have earned the trust of customers and supply products all over the world.

To purchase Power Resistors, send an email request to:

[email protected]

And we will provide you a commercial offer for delivery.

Datasheet (pdf specification) for Fixed Power Resistors:

PDFDatasheet PDF for Fixed Power Resistors

Guide for using and operation of resistors:

  • Solder the wires to the resistor leads in specially designed holes.
  • When installing resistors in equipment recommended to use Sn40Pb60 solder. Soldering iron core temperature is 300°C. Soldering iron power is 65W. The flux should consist of 25% by weight of rosin and 75% by weight of isopropyl or ethyl alcohol. Soldering time 5 s.
  • The voltage that can be supplied to the resistor must not exceed the value calculated on the basis of the nominal (or allowable) power Pnom and nominal resistance Rnom according to the formula:
    Vmax = (Pnom × Rnom)0.5
  • Resonant frequency value - 1500 Hz.
  • 95-percent work resource - 30 000 hours.
  • It is allowed to operate resistors under the influence of gas media of this composition (without the formation of an explosive mixture):
    • nitrogen – up to 96%;
    • oxygen – up to 50%;
    • carbon dioxide – up to 3%;
    • hydrogen – up to 20%;
    • helium – up to 1%;
    • argon – up to 1,5%.
  • Operation of resistors during and after exposure to atmospheric pressure reduced to 10~5 mm Hg is allowed.
  • In electrical circuits with voltages above 500V resistors must be used with additional insulation at the mounting points.
  • When using resistors in equipment with vibration loads from 1 to 2500 Hz with an acceleration of 176.6 m/s2 (18g), the resistor leads must be soldered with a 0.5 mm2 wire cross-section with insulation by a polychlorovinyl tube Ø4 mm and length of 15-20 mm – for resistors 5-25 W, and Ø5 mm and length of 15-20 mm – for resistors 50-100 W.
  • Tensile force value should be 20N (2 kgf).
  • The upper frequency of the range in which there should be no resonant frequencies – 1000 Hz.
  • Maximum surface temperature of the resistor is not more than 250°C.

Graph of the resistor power reduction:

The load power should be reduced based on the derating curve once the ambient temperature exceeds the rated values.

Resistor Resistance Calculation

Resistor Connection Diagram

Comparative performance of high power resistors:

Resistor Series Type Structure Power, W Resistance Range, Ohm Maximum Voltage, V Resistance Tolerance
img FPT, RX20 Fixed Wire Tubular Ceramic 3 - 160W 1 R - 100 K ~1000V
± 5%
± 10%
img APT, RX20 Adjustable, Variable Wire Tubular Ceramic 3 - 160W 1 R - 100 K ~1000V
± 5%
± 10%
img SQP, RX27, CR-L Fixed Wire Ceramic Cement 5 - 25W 0,01 R - 100 K ~1500V
± 5%
img AH, HS, RX24 Fixed Wire Ceramic, Aluminum Case with Radiator 5 - 1000W 0,01 R - 100 K ~2500V
± 5%
GİZEM GÖZÜN 26.01.2021 at 13:04
I'm Gizem, I'm a chemical engineer. I'm interested in making ceramic stuffs as a hobby. Would you please give some explanation about my questions below;
1) If I only mix SiO2 and Fe2O3 (3:1), can i get a suitable product without using other components?
2) Can i use water as fastener? or would you suggest me another fastener?
3) At which temperature should i mix them?
Thank you for your interest, Kind Regards
26.01.2021 at 14:43
Hello, Gizem. The mass of ceramic is produced by grinding and mixing with water of different components: clay, feldspar, sand, kaolin. The proportions of these materials are different percentages, depending on what and with what characteristics you need to get a ceramic mass.
Each manufacturer of ceramic mass has its own recipes and its own raw materials, which are available in its region.
There are also books on ceramics that specify the chemical composition and approximate recipes for ceramic masses.
Roman 27.06.2022 at 00:03
Is It need to apply vaselin or thermal past at Thyristor surfaces then attach to radiator/current leading parts?
Maksim 27.06.2022 at 10:39
When assembling thyristors, diodes with heat sinks, it is recommended to lubricate the contact surfaces with a thin layer of heat conducting paste to improve the heat transfer parameters. But this is not a prerequisite for assembly.

CancelWrite Comment or Review:

Here you can ask a question about the technical features of the products or write a review about the company.

We also invite you for discussion about electrical engineering and electronics, share your experience, knowledge, express your opinion.

Please send commercial request using the Cart or E-mail (not here).

Featured Products:


Tags: Power Resistor 4.7 Ohm 150W 160W, Tolerance ±5% ±10%, High Power Resistor 4.7 Ohm 160 Watt, Fixed type wire wound resistor 4.7 Ohm 160 Watts, high power load resistors 4R7 160W, resistors for industrial use, resistor chassis mounting, panel mount resistor, power resistors manufacturer, suppliers & exporters, certificate, price, technical specification of power resistors


Selected Products: